Automotive thermal imaging and car electronics manufacturer since 2006 · Shenzhen, China
Buyer guide

What to verify before private-labeling a car thermal night vision system

Get six things in writing before your brand goes on a car thermal camera: the exact detector and lens, test reports that cover your model, the compliance route for each market, who owns the firmware and any custom tooling, the warranty and dead-on-arrival terms, and a sample to pilot to production plan with the hardware and firmware version frozen.

Key takeaways

  • Decide the branding level first: software branding, packaging, or engineering changes. Cost, minimums and lead time follow from it.
  • Ask for the detector, pixel pitch, lens focal length and NETD with test conditions. Resolution alone does not tell you range.
  • Test reports must name the model you buy. If only branding changes, get a written statement that the hardware is identical.
  • When your brand is on the product, you take on the manufacturer duties in several markets. Plan the compliance file before the artwork.
  • Put ownership of branded firmware builds, artwork and custom tooling in the contract.
  • Approve a branded pre-production unit, run a small pilot, and freeze the hardware and firmware version for production.

This checklist is written for distributors, importers and 4WD or truck accessory brands who want to sell a car thermal night vision system under their own name. It follows the order in which problems usually appear: what you are actually changing, whether the camera is good enough, whether the paperwork holds up in your market, who owns what, and how to get from one sample to a production run that matches it.

Each section ends with the questions to send a supplier. The full list is collected in section 11 so you can paste it into an RFQ.

1. Decide what "private label" means for your order

Suppliers use private label, OEM and ODM loosely. Before comparing quotes, write down which of three levels you want. A quote for "OEM" from one factory may mean a logo on the start-up screen; from another it may mean a new housing. Comparing them side by side is meaningless until the scope is the same.

LevelWhat changesCost and minimumsWhat you approve
Software brandingYour start-up video, interface logo, alert voiceLowest set-up effort; usually the smallest branded orderA pre-production unit running your branded firmware
Packaging and printRetail box, manual cover, labels, quick-start card, default interface languagePrinting minimums apply; artwork in your hands earlyPrinted proofs plus one fully packed sample
Engineering changesHousing, cable length or connectors, lens, host hardware, alert logic, recognition featuresTooling, testing and time; needs a feasibility reviewEngineering samples, updated test reports, written change list

Most distributors start at the first level, add their own packaging on the second order, and only move to engineering changes once sales justify the tooling. Software branding also has a practical advantage: the hardware stays identical to the supplier’s tested model, so existing test reports remain relevant.

Ask the supplier: which items can change at each level, the minimum order for each, and whether a set-up cost applies.

2. Pin down the thermal camera core

The detector and lens decide what the driver sees. Everything else in a car thermal camera system, from the screen to the box, is packaging around them. A datasheet that lists only "384 thermal" and a range in metres is not enough to compare suppliers, because two cameras with the same resolution can see very different things.

SpecWhat to ask forWhy it mattersRed flag
Detector type and pixel pitchMaterial (VOx or amorphous silicon), pixel pitch in μm, detector makerPitch and lens together set how many pixels land on a pedestrianOnly "high-definition thermal" with no pitch stated
ResolutionNative detector resolution, not the display or upscaled video sizeA 1024 × 600 screen does not add thermal detailResolution quoted as the monitor size
Lens and field of viewFocal length in mm and horizontal × vertical FOVChanges range and coverage more than any other single partFOV listed with no focal length
NETDValue in mK with the temperature and F-number it was measured atLower NETD keeps contrast on mild, humid nightsA NETD figure with no test conditions
Frame rateDetector frame rate and the rate the AI processesLow frame rates stutter at road speedDifferent numbers in the datasheet and the manual
Window and defrostWindow material, heater switch-on and switch-off temperaturesA frosted window blinds the camera on winter mornings"Heated" with no temperatures

As a reference point, our standard cameras use an uncooled VOx detector with a 12 μm pitch, a 9.1 mm lens, NETD of 40 mK or lower at 25 °C and F1.0, and a heated window that switches on below 2 °C and off above 7 °C. A supplier who can give you the same level of detail for every configuration is easier to hold to a specification later.

Also check that the datasheet, the user manual and the quotation agree. Mismatched numbers between documents are common and usually mean one of them is out of date. Ask which document is binding, and have the binding one referenced in your purchase order.

Ask the supplier: detector type, pitch and maker; native resolution; focal length and field of view; NETD with test conditions; frame rate; heater temperatures; which document is the binding specification.

3. Ask how every range was measured

Range figures sell car thermal cameras, and they are the easiest numbers on a thermal camera datasheet to inflate. There are two different kinds, and datasheets often mix them.

  • Viewing range: how far away a driver can see a target on the screen. Usually quoted with the Johnson criteria as detection, recognition and identification (DRI) distances.
  • AI or alert range: how far away the software marks a target and sounds an alert. This depends on the recognition model, the warning zones and the speed, and is always shorter than the detection distance.

For each figure, ask for the target size, the pixel criterion used and the conditions. A pedestrian range calculated for a 1.8 m person at two pixels is a detection distance; quoting it as a warning distance is misleading. Our product pages list AI ranges for a person taller than 1.7 m, a vehicle wider than 2.3 m and an animal taller than 1.5 m, and state that weather, thermal contrast and mounting shorten them. Our resolution and lens guide shows how DRI distances follow from pixel pitch and focal length.

The only range that matters to your customers is the one on their roads. Test samples on your own vehicles, at night, on a mild humid evening as well as a cold clear one, because low thermal contrast is where cheap detectors fall short.

Ask the supplier: for each range, the target size, pixel criterion, conditions and whether it is a viewing or an alert range.

4. Check thermal camera interfaces and the installation path

Returns of private-label thermal cameras are more often about installation than image quality. A system that is hard to fit in your customers’ vehicles will come back, whatever the detector.

  • Camera position. Glass blocks long-wave infrared, so the camera must be mounted outside, usually in the grille or on a bull bar. Confirm the bracket suits the vehicles you sell into. See why a thermal camera cannot see through a windshield.
  • Cable and connectors. Cable length from grille to cabin, connector type, and whether the connector passes through a firewall grommet. Ask for an extension option for trucks and long-wheelbase vehicles.
  • Power. 12 V and 24 V support, fuse location, current draw, behaviour during engine cranking and whether it can be hardwired to ignition.
  • Outputs. Alarm signal output for a buzzer or relay, video output for a fleet DVR, or a host that feeds an existing screen. Our integration hosts cover wired CarPlay, Android head units and AHD, HDMI and CVBS displays.
  • Documentation. An installation guide with photos, wiring diagram and the warning-zone set-up. Your installers will judge the product by this before they see the image.

Ask the supplier: bracket drawings, cable length and connector photos, supported voltages, current draw, available outputs and the installation guide in the language you sell in.

5. Request automotive electrical and environmental tests

A car thermal camera in a grille lives through engine-bay heat, car-wash pressure, stone chips, winter salt and the electrical noise of a vehicle supply. Consumer electronics tests do not cover this. Ask which automotive tests were run and request the reports, not only certificates.

StandardWhat it coversWhat to ask
ISO 7637-2Electrical transients on the supply line: load dump, inductive spikes, switching noisePulses applied, test level, and pass class for 12 V and 24 V
ISO 16750-2Supply voltage range, cranking dips, reverse polarity, over-voltage and jump-startWhich clauses were run and the operating state after each
ISO 16750-3Vibration and mechanical shock for the mounting locationProfile used (body, grille or bumper) and duration per axis
ISO 16750-4Low and high temperature, temperature cycling, damp heatCold-start result at the lowest rated temperature
IEC 60529IP code: dust and water ingress for camera and displayReport for the camera with its cable and connector fitted
UN Regulation No. 10Vehicle EMC for electronic sub-assemblies (E-mark)Whether an approval exists, its number and the models listed

Not every supplier will have every report. That is not automatically a reason to walk away, but it changes your risk. If a report is missing, ask whether the supplier will run it for your order and who pays, or plan your own testing at a local lab before launch.

Read the scope page of each report. Check the model numbers, the hardware version, the lab name and accreditation, and the date. A report for a different camera module, or one that tested only the display, does not cover the camera in the grille.

Ask the supplier: full reports for the tests above, the models and hardware versions each one covers, and the cold-start result at the lowest rated temperature.

6. Plan compliance for each market before the artwork

When the product carries your brand, you may become the legally responsible manufacturer or importer. In the EU, anyone who places a product on the market under their own name or trademark takes on the manufacturer duties, including the declaration of conformity and the technical file. Similar responsibility sits with the local supplier or importer in other markets.

MarketUsual route for a 12 V / 24 V vehicle display and cameraNote
European UnionCE: EMC Directive 2014/30/EU, RoHS 2011/65/EU; WEEE and REACH duties for the importerSome buyers and fleets also ask for a UN R10 E-mark. The brand owner placing the product on the market carries the manufacturer duties.
United KingdomUKCA or CE under the current GB rules; UK RoHSCheck the current rules for your product group before printing labels.
United StatesFCC Part 15 Subpart B for unintentional radiatorsThe FCC label and supplier declaration name the responsible party in the US.
CanadaICES-003 for digital apparatusAn ICES-003 compliance statement goes on the label or in the manual.
Australia and New ZealandRCM under the ACMA EMC arrangements; supplier registrationThe local supplier holds the compliance records and registration.

General guidance only, not legal advice. Rules change and depend on how the product is installed and sold; confirm the route with a compliance consultant or test lab in your market.

Three practical points. First, the label artwork, the manual and the declaration must carry your company name and address where the rules require it, so collect these before the printer needs them. Second, if the supplier’s reports name its own model number, ask for a written statement that your branded product uses identical hardware, so you can reference the reports in your own file. Third, keep the reports, the statement and the approved sample together; they are your evidence if a market authority asks.

Ask the supplier: current CE, RoHS, FCC and EMC reports with model coverage, whether a UN R10 approval exists, and a hardware-identity statement for your branded version.

7. See how the factory builds and checks each thermal camera

A visit is ideal; a live video walk-through works when travel is not practical. You are not judging how modern the building looks. You are checking whether the processes that protect your brand exist and are recorded.

  • Incoming inspection of detectors, lenses and screens, with records you can ask to see.
  • Assembly and focus. How the lens is focused and fixed, and how that is checked.
  • Image calibration. Non-uniformity correction and a test against a reference heat source before the camera is sealed.
  • Burn-in or ageing of finished systems for early failures.
  • Waterproof testing of sealed cameras, by sample or for every unit.
  • Final inspection with a checklist that you can receive per shipment.

Ask who the factory and the R&D team are, and how they relate. Many thermal products are developed by one company and built by another. That is normal, but you should know which legal entity signs your contract, issues the invoice and handles warranty claims.

Ask the supplier: a production video, an example final inspection record, the legal entity for the contract, and how long the product has been in production.

8. Agree who owns private-label firmware, artwork and tooling

Ownership questions rarely come up on the first private label order and often decide the third. Put the answers in the contract while both sides are keen.

  • Firmware. Suppliers normally keep the source code and build a branded version for you. Agree that your build is archived, reused on repeat orders and updated when the base firmware changes, and that firmware updates are released to you with notes.
  • Artwork. Your logo, start-up video, voice prompts, box design and manual text belong to you. The supplier should not use them for other buyers.
  • Tooling. If you pay for a custom housing or bracket mould, state who owns it, where it is stored and whether it can be moved.
  • Exclusivity. If you want exclusive rights for a country or a sales channel, expect a minimum annual volume in return. Define what "same product" means, because the supplier can still sell its own brand.
  • Changes. The supplier should notify you before changing the detector, lens, main chip or firmware in your product, even if the specification stays the same.

Ask the supplier: their standard terms on firmware builds, artwork use, tooling ownership, exclusivity and change notification.

9. Fix warranty, dead-on-arrival and spare parts terms

Your end-user warranty on a private label thermal camera can only be as good as the terms behind it. Before you print "2-year warranty" on your box, check that the supplier backs it.

  • Dead on arrival. How DOA units are reported, with what evidence, and whether they are replaced in the next shipment or sent immediately.
  • Spare units. Some suppliers ship a small percentage of extra units instead of handling single returns. Agree the percentage and what it covers.
  • Replacement and repair periods. How long a unit is replaced outright, and how long it is repaired after that. Who pays shipping each way.
  • Spare parts. Whether cameras, cables, brackets and power adapters can be bought separately. A cracked camera on a 4WD should not mean replacing the whole kit.
  • Firmware updates. How updates reach units in the field, for example from a USB drive, and whether your installers can apply them.
  • Support. Response time for technical questions, and whether the supplier will answer your installers directly or only through you.

Ask the supplier: written warranty terms for distributors, the DOA process, spare-part prices, and how firmware updates are delivered.

10. Move a private-label order from sample to production in steps

The most expensive private-label problems are thermal cameras that do not match the approved sample. A staged process with written approvals at each step prevents most of them.

StageWhat you receiveWhat you approve
Evaluation sampleStandard unit in the configuration you plan to sellImage, alerts, menus, install on your own vehicles
Branded pre-production unitYour start-up video, logo, voice and packaging on a real unitBranding, language defaults, packed carton, label text
Pilot runA small batch built on the production lineOut-of-box failure rate, installer feedback, packaging in transit
ProductionBuilt to the approved unitHardware and firmware version confirmed in writing; inspection report

Keep the approved pre-production unit as your golden sample. Write its hardware and firmware version on the purchase order, and ask for the same versions to be confirmed on the inspection report for each shipment. If the supplier needs to change a part, they should send a new sample for approval before the change reaches your stock.

Ask the supplier: lead time for each stage, whether a pilot run is possible at a smaller quantity, and whether they will confirm hardware and firmware versions per shipment.

11. Score thermal camera suppliers and send the same RFQ to each

A simple scorecard keeps the comparison of thermal camera suppliers honest, especially when one is much cheaper. Weight it to your business; a fleet integrator might give documentation more points, a 4WD brand might weight warranty and spare parts.

AreaPointsWhat earns the points
Thermal core and image20Complete, consistent specs; image quality on your roads
Test reports and compliance20Reports that cover your model, current lab, readable scope
Factory and quality control15Visible processes, final inspection records, production video
Branding and ownership terms15Clear rules for firmware builds, tooling and artwork
Warranty and spare parts15Written terms, spare cameras and cables, repair path
Documentation and support10Manual, installation guide, datasheet, response time
Commercial terms5Price by quantity, MOQ, lead time, payment terms
Total100

Questions to paste into your RFQ:

  1. Which detector, pixel pitch, lens focal length and field of view does each configuration use?
  2. What is the NETD, and at what temperature and F-number was it measured?
  3. For each range figure, what target size, pixel criterion and conditions apply? Is it a viewing or an alert range?
  4. At what temperatures does the window heater switch on and off?
  5. Which vehicle voltages are supported, what is the current draw, and how does the system behave during cranking?
  6. What outputs are available: alarm signal, video, integration with existing screens?
  7. Which automotive tests (ISO 7637-2, ISO 16750, IEC 60529, UN R10) have been run, and which models do the reports cover?
  8. Which CE, RoHS, FCC or other reports cover the configuration I am buying?
  9. Will you provide a written statement that my branded version uses the same hardware as the tested model?
  10. What can I change at each branding level, and what are the minimums and set-up costs?
  11. Who owns my branded firmware build, artwork and any custom tooling?
  12. Will you notify me before changing the detector, lens, main chip or firmware?
  13. What are the replacement, repair and DOA terms for distributors, and who pays shipping?
  14. Can cameras, cables and brackets be bought as spare parts?
  15. What are the lead times for samples, a branded pre-production unit, a pilot run and production?
  16. Will you confirm the hardware and firmware version on each shipment’s inspection report?

How we handle this at iSun

iSun Digitech Limited has built vehicle electronics in Shenzhen since 2006, and VERYTEK AI Tech Limited has developed the thermal imaging and AI since 2013. This is how we answer the checklist above for distributors.

  • Branding: your start-up video, interface logo, alert voice on the standard 5-inch kit and 7-inch system; packaging agreed per order; hardware changes through an engineering review first. Details on our private label and OEM page.
  • Specifications: detector, pitch, lens, NETD and heater temperatures are published for every configuration, with the target sizes behind each range.
  • Reports: we send the product certificates and test reports for the configuration you are quoting, and confirm in writing which models they cover.
  • Samples and production: evaluation samples in the configuration you plan to sell, a branded pre-production unit for approval, and the hardware and firmware version confirmed in writing for each production order.
  • Warranty: The user manual lists a 3-month replacement period for non-human damage and a 2-year repair warranty. Terms for your order are confirmed in the quotation.

Datasheets and manuals are on the downloads page. To start, send your market, the configurations you want to stock and your branding scope through the inquiry form, or write to me at jennie@isungps.com.

Quick answers

What is the difference between private label, OEM and ODM for car thermal cameras?

Private label usually means the supplier’s standard product with your branding on the screen and box. OEM is often used the same way in aftermarket trade. ODM means the supplier also designs or changes the product for you, such as a new housing or different alert logic, which needs an engineering review, tooling and new tests.

Do test reports still apply when the product carries my brand?

A report covers the tested model and its hardware. If only the start-up video, logo and box change, ask the supplier for a written statement that the hardware is identical to the tested model. If you are the brand owner in a market such as the EU, you sign the declaration of conformity and keep the technical file.

Who owns the firmware in a private-label thermal camera?

In most private-label deals the supplier keeps the source code and builds a branded firmware version for you. Agree in writing that your branded build is stored and reused for repeat orders, and what happens to your artwork and custom tooling if you change supplier.

How many samples should a distributor test before ordering?

Test at least one unit of each configuration you plan to stock, installed on your own vehicles, then approve one branded pre-production unit. A short pilot run before full production shows out-of-box failures and packaging damage that one sample cannot.

Should the warranty for distributors differ from the end-user warranty?

Often yes. Agree how dead-on-arrival units are replaced, whether the supplier ships a percentage of spare units with each order, how long repairs take and who pays shipping. Then set your end-user warranty from those terms.

Is a car thermal night vision system an ADAS?

An aftermarket system assists the driver with a thermal view and alerts. It does not brake or steer, and it is not a type-approved driver assistance system. Say this clearly in your own marketing and manual.

Tell us your market and vehicles. We will recommend a configuration.

Share your company, target market, vehicle types and expected quantity. We reply with a configuration, sample terms and pricing.